-
Advantages of ampoule wire drawing and filling machine
Time of Update: 2022-05-06
5. The filling station of the ampoule wire drawing filling and sealing machine is equipped with multiple filling heads, in addition to filling liquid, it can also meet the requirements of filling compressed air and nitrogen filling at the same time; the whole machine runs smoothly in and out of bottles, and the qualified rate of finished products is high.
-
In this article, what are the characteristics of the top-entry turtle-back filter?
Time of Update: 2022-05-06
The following editor briefly introduces the characteristics of the top-entry turtle back filter?
Through the above content, the editor hopes to help you understand the top-entry turtle-back filter .
-
What details are needed when the small heat and cold machine is turned on
Time of Update: 2022-05-06
It is necessary to check whether there are few pieces of the product, there is loss, and whether it can be used normally is the same, so the following editor will explain to you what details you need to pay attention to when starting the small hot and cold all-in-one machine .
-
What are the precautions for small high and low temperature cycle devices
Time of Update: 2022-05-06
The refrigeration system of small high and low temperature circulation device consists of refrigerant and four major parts, namely compressor, condenser, expansion valve and evaporator .
-
How to standardize the operation of small hot and cold dual-purpose chillers
Time of Update: 2022-05-06
So how to carry out the normative operation of the small hot and cold dual-purpose chiller, many people want to know .
After using the small hot and cold dual-purpose chiller, it should be cleaned regularly, and the follow-up work should be done during each operation.
-
What are the technological requirements of the small high and low temperature circulating temperature controller
Time of Update: 2022-05-06
The small high and low temperature circulating temperature controller is used in the pharmaceutical and chemical industry to heat up to the temperature required by the process through electric heating, and indirectly transfer heat in the mode of circulating pump phase to make the temperature meet the requirements of the production process.
-
Regular replacement time of purified water equipment consumables
Time of Update: 2022-05-06
The consumables that need to be replaced in the purified water equipment are: quartz sand, activated carbon, resin, reverse osmosis membrane, precision filter element, etc.
The reverse osmosis membrane is the core of the purified water equipment and requires careful maintenance, including cleaning and replacement .
-
Knowledge of common faults in small chemical high and low temperature cycle devices
Time of Update: 2022-05-06
1. The equipment thermometer fails, causing the small chemical high and low temperature circulation device to overheat .
2. The motor of the small chemical high and low temperature circulation device is reversed.
-
Daily maintenance of ampoule wire drawing filling and sealing machine
Time of Update: 2022-05-06
It is strictly forbidden to use too large tools or excessive force to disassemble the parts, so as to avoid damaging the parts or affecting the performance of the machine .
-
An article to understand the main structural components of the double cone mixer
Time of Update: 2022-05-06
Double cone mixer refers to a mixing device that mixes various powders uniformly through a rotating tank .
The device used for power distribution, the power lines of the electrical equipment attached to the rotating tank are all input from this .
-
Precautions for the installation of automatic ampoule wire drawing filling machine
Time of Update: 2022-05-06
To do this, you must first disconnect the belt between the side-connected motor and the main shaft, and then open the switch to check whether the belt pulley of the motor rotates clockwise .
-
Characteristics and precautions of semi-automatic liquid filling machine
Time of Update: 2022-05-06
5. The main power of the semi-automatic liquid filling machine is the air source, and customers need to provide their own air compressor equipment .
3. Before disassembling and washing the semi-automatic quantitative filling machine, please be sure to turn off the gas source and power supply .
-
Refrigeration and heating integrated machine compressor knowledge introduction
Time of Update: 2022-05-06
Pressure protection: The pressure control of the integrated refrigeration and heating machine is generally composed of a high-pressure control part and a low-pressure control part .
3. Temperature protection: The cooling and heating integrated machine is equipped with a temperature control system at the exhaust port .
-
Common faults and troubleshooting methods of explosion-proof small high and low temperature cycle integrated machine
Time of Update: 2022-05-05
3. The cooling effect of the explosion-proof small high-low temperature cycle integrated machine is reduced, and people feel electric shock when touching the metal part of the box: Remedy: Use a multimeter to measure the leakage, and use the segmentation method to check .
-
Product performance and advantages of explosion-proof high and low temperature cycle integrated machine for pharmaceutical and chemical industry
Time of Update: 2022-05-05
The pharmaceutical and chemical explosion-proof high and low temperature cycle machine can automatically adjust the heating or cooling function according to the specific requirements of use .
-
Notes on the use of small refrigeration and heating circulators
Time of Update: 2022-05-05
It only needs to gently turn the valve needle and press the cover tightly to achieve a good sealing effect .
6. The controller should be placed flat on the operating table, and the surrounding medium does not contain conductive dust and corrosive gases .
-
Knowledge of the use of laboratory small high and low temperature cycle machine
Time of Update: 2022-05-05
1. The flow of material and the power of the motor speed may cause resonance at a certain point.
Install the machine first, then wire it by a professional electrician, and turn it on .
7. Pay attention to the damage caused by high temperature to the human body.
-
What problems should be paid attention to in the use of automatic capping machine
Time of Update: 2022-05-05
When screwing the capping cap, pay attention to the operation action.
When using daily, pay attention to the operating environment, and different automatic capping The capping machine has an instruction manual .
-
Process description of gel filling and labeling machine
Time of Update: 2022-05-05
7) Use non-breakable materials where glass is normally used for all equipment parts .
6) Wire markings and terminal block markings are permanent markings and refer to Chinese electrical engineering standards .
-
Principle and Application of Sound Level Meter
Time of Update: 2022-05-05
Sound level meter is the most basic instrument for measuring noise.
The sound level meter adopts digital detection technology, which greatly improves the stability and reliability of the instrument .