-
The advantages and scope of application of the automatic multi-head liquid filling machine
Time of Update: 2022-05-05
Such as hand soap, care solution, oral solution, hair care solution, hand soap, skin care solution, disinfectant, liquid foundation, antifreeze, shampoo, eye wash, nutrient solution, injection, pesticide, medicine, cleaning, bathing Liquid filling machine for dew, perfume, edible oil, lubricating oil and special industries .
-
How to avoid mistakes in the operation of the laboratory explosion-proof high and low temperature cycle integrated machine
Time of Update: 2022-05-05
8. Wipe each interface with a soft cloth (can be replaced with a napkin), and then apply a little vacuum grease .
-
How to improve the freeze-drying efficiency of Sihuan freeze-drying vacuum freeze-drying machine
Time of Update: 2022-05-05
Generally, the thinner the material thickness, the faster the heat and mass transfer, and the shorter the drying time .
The mass transfer rate mainly depends on the temperature and pressure of the sublimation interface and the surface of the drying layer .
-
An article to understand the main structural characteristics of wet granulator
Time of Update: 2022-05-04
Pellet manufacturing device: the rotating drum is horizontally installed under the hopper, and there are bearing supports at the front and rear.
When assembling and disassembling, as long as three screws are unscrewed, the front bearing seat and the rotating drum can be pulled out in sequence .
-
The key points of using Sartorius electronic balance
Time of Update: 2022-05-04
3. The calibration mechanism of Sartorius analytical balance is usually divided into three types: (1) Fully automatic calibration: it contains standard weights and motor servo mechanism, and the calibration can be completed within tens of seconds by pressing a function key.
-
What are the requirements of the labeling machine for labels?
Time of Update: 2022-05-04
It is required that the surface of the backing paper is uniformly coated with silicon, and the release force is consistent; the thickness is uniform, and it has good tensile strength to ensure that the label does not break; the thickness is uniform, and it has good light transmittance to ensure that the sensor can correctly identify the position of the label .
-
Design principle of automatic filling machine
Time of Update: 2022-05-04
3. The design of the fully automatic filling machine should mainly be based on the specific needs of the enterprise, adopt the innovative design method of functional principle, and design a new type of filling equipment that meets the production needs of the enterprise, which can not only improve work efficiency, but also reduce damage.
-
What are the instructions for use and maintenance of box-type resistance furnaces?
Time of Update: 2022-05-04
What are the instructions for use and maintenance of box-type resistance furnaces?
Turn off the electric furnace switch after the working time is up, and take out the sample after cooling .
The above is the introduction to the instructions for use and maintenance points of the box-type resistance furnace.
-
Six Features of High Purity Nitrogen Generator
Time of Update: 2022-05-04
The new membrane separation technology uses PCAN carrier and precious metal catalyst for the catalytic layer, so that the electrolytic cell has high catalytic efficiency, large gas production, and high nitrogen purity.
-
What is the control core of the couplant filling machine?
Time of Update: 2022-05-04
The fully automatic couplant filling machine is designed with a pneumatic-based linear motion method, and uses the programmable controller, various detection and induction devices and the time difference between the cylinder and the cylinder to stop the container at the filling position.
The high-viscosity liquid filling machine has reasonable design, compact model and convenient operation.
-
The advantages of automatic filling machine
Time of Update: 2022-05-04
The fully automatic filling machine has a reasonable structure design, adopts the international new process design, and the internal parts are made of stainless steel, which is in line with the national GMP Standard, packaged products can reassure consumers .
-
Several points that cannot be known when using a dust particle counter
Time of Update: 2022-05-04
When there are loose particle materials, dust sources, and spray places in the measurement place, it must be kept at least twelve inches away from the inlet pipe .
7. The laser dust particle counter should be used in a clean environment to prevent damage to the laser sensor .
-
What are the performance characteristics of the vacuum feeder in a few minutes?
Time of Update: 2022-05-04
This conveying method can prevent dust pollution, improve the working environment, reduce the pollution of the environment and personnel to materials, and improve the cleanliness; 2.
The choice of material conveying method .
-
What are the operating procedures of the spray filling machine
Time of Update: 2022-05-04
After that, turn on the main power again, the power indicator is on, the fault indicator and emergency stop indicator are not on, then the starting conditions are met, press the start button on the control box and the start switch at the filling place, and the buzzer will sound three warnings.
-
How the alcohol filling machine works
Time of Update: 2022-05-04
1. The filling valve of the automatic alcohol filling machine adopts the filling principle of the filling industry, reasonable design, excellent quality and precise processing parts to ensure the liquid level requirements after filling .
-
Principle and application of traditional Chinese medicine clarification tubular separator
Time of Update: 2022-05-04
The working principle of the traditional Chinese medicine clarification tube separator: The main shaft drives the drum to rotate at high speed around its own axis, forming a strong centrifugal force field in the drum .
-
What should be paid attention to in the valve of the high and low temperature cycle temperature control system
Time of Update: 2022-05-04
The thermal expansion valve used in the high and low temperature cycle temperature control system requires horizontal installation .
4. The integrated valve of the high and low temperature cycle temperature control system should be directly installed on the stop valve at the outlet of the equipment.
-
What should I pay attention to when buying a filling machine?
Time of Update: 2022-05-04
There are many kinds of products in the current filling machine market, and all kinds of brands are emerging one after another, which is so dazzling that it is impossible to start .
The product quality of the filling machine .
-
How are Shanghai Shenggang ampoules sealed?
Time of Update: 2022-05-04
Hydrogen-oxygen flame ampoule sealing machine uses gas, oxygen or water and electricity as fuel.
At this time, since the contact is kept at a certain distance by the micro switch gap, the coil power supply is disconnected, and the ejector rod is tied to the right by the force of the spring.
-
The working principle and application scope of the high-efficiency boiling drying granulator
Time of Update: 2022-05-04
The working principle of the high-efficiency boiling drying granulator: the material powder particles are in a circular fluidized state in the raw material container (fluidized bed), and are preheated and mixed by the purified heated air, and the binder solution is atomized and sprayed into , make several particles aggregate into agglomerates containing a binder, due to the continuous drying of the material by the hot air, the moisture in the agglomerates evaporates and the binder solidifies.