What are the adjustment methods of the automatic spray filling machine

Adjustment of the feeding half a.
Adjust the bottle blocking plate A on the feeding half upward to shorten the bottle feeding stroke; adjust downward to extend the suitable bottle feeding stroke
.

b.
Adjust the positioning bottle position left and right so that the movable teeth are aligned with the bottle position when running, so that the bottle can be smoothly fed into the positioning teeth
.

c.
Adjust the bottle blocking plate B so that the width of the bottle inlet is about 22 mm
.

Adjustment of perfusion components The function of perfusion components is to deliver the liquid medicine to each easy-pull bottle in time through the dispenser, one-way valve and needle, so the needle must enter the bottle mouth properly, and the filling time must be appropriate
.

a.
Adjust the cam A of the side to rotate forward or reversely so that the needle is inserted into the bottle mouth just after the empty bottle enters the toothed position
.

and lift the needle before leaving the toothed position
.

b.
Perfusion time adjustment: Turn cam B forward or reverse to adjust the injection to start immediately after the needle enters the bottle mouth, and stop the injection before the needle leaves the bottle mouth
.

 　　c.
Adjustment of liquid volume: loosen nut 1 and adjust the ejector rod in the direction of D, the liquid volume will increase; adjust the liquid volume in the direction of C to reduce the liquid volume, while adjusting the nut 2 in the direction of F to reduce the volume of liquid, and adjust in the direction of E to increase the liquid volume When adjusting, pay attention to the limit position of the drug injector to avoid damage to the drug injector.
Generally, it is advisable that the bottom of the drug injector reaches the drug spit not less than 15 mm, and the longer the perfusion time, the better
.

 　　Stopping device When the tooth plate is moved to move the bottle to the position of the stop tooth, the convex surface of the cam 7 is separated from the swing plate 6, and the swing plate 6 is pulled by the tension spring 4 to swing clockwise, and the swing plate 6 drives the The bottle press bolt 2 moves down until it touches the bottle 3.
At this time, the steel wire rolling head 5 and the swing plate 6 should be adjusted to contact and adjust the adjusting screw 8 so that the ejector bolt 1 extends about 4 mm, and an empty bottle appears at this position.
, the bottle-pressing bolt 2 and the rocking plate 6 continue to move down due to the action of the tension spring 4, until the steel wire rolling head 5 pulls the steel wire to make the ejector pin 1 separate from the ejector bar 9, so it cannot drive the medicine dispenser to work, and automatically stops pouring the medicine liquid
.

 　　1.
Adjustment of the upper arm This machine can be used to roll 5-500ml bottle caps.
When rolling bottles of different specifications, just put the bottle of this specification on the tray, hold the cross arm with one hand, and loosen the left side of the cross arm with the other hand.
nut, make the cross arm drop or rise until the capping head and the bottle cap are about 20 mm, tighten the nut, and then use the random Allen wrench to close the support ring against the cross arm and then lock the support ring
.

(Note) When tightening, pay attention to the alignment of the capping head and the bottle cap
.

 　　2.
Adjustment of the V-shaped support block Put the bottle into the lower V-shaped support, loosen the two screws on the support, and move the bottle and the lower V-shaped block together until the capping head is aligned with the bottle cap.
, and tighten the two screws on the V-block
.

 　　3.
Specific operation method 1.
Put the bottle filled with liquid and put the lid on the lower tray, lean on the V-shaped support, hold the bottle with one hand, and pull the handle backward and tighten with the other hand, then the tray Lift the bottle up until the cap is pressed against the crimping head
.

 　　2.
After the bottle cap and the capping head are pressed tightly, the three capping cutter heads that are continuously rotating rotate several times to tighten the bottle cap
.

(Note) The motor must run clockwise
.

 　　3.
Push the handle forward, so that the rolled cap will return to its original position with the tray, and the whole operation process is completed.
Repeat the above operation every time you roll a bottle cap in the future
.

 　　Fourth, the adjustment of the capping head The machine is equipped with multiple capping heads, which can be selected according to the size of different bottle caps
.

Try it on the bottle before using it
.

 　　1.
If the cover is not rolled tightly, you can unscrew the capping head locking nut and unscrew the upper capping head counterclockwise, and then lock the upper fixing nut
.

 　　2.
The lid is rolled too tightly, and there is a phenomenon of rotary cutting of the bottle cap
.

Unscrew the locking nut of the upper rolling cap head and screw it into the upper rolling cap head in a clockwise direction, and then lock the upper fixing nut
.

 　　3.
The lower edge of the bottle cap is not tightened tightly, and the eccentricity of the three cutter heads can be appropriately adjusted according to the actual situation
.

If it is too tight, the bottle may be crushed, and the eccentricity of the three rolling heads can be adjusted appropriately.