-
Categories
-
Pharmaceutical Intermediates
-
Active Pharmaceutical Ingredients
-
Food Additives
- Industrial Coatings
- Agrochemicals
- Dyes and Pigments
- Surfactant
- Flavors and Fragrances
- Chemical Reagents
- Catalyst and Auxiliary
- Natural Products
- Inorganic Chemistry
-
Organic Chemistry
-
Biochemical Engineering
- Analytical Chemistry
-
Cosmetic Ingredient
- Water Treatment Chemical
-
Pharmaceutical Intermediates
Promotion
ECHEMI Mall
Wholesale
Weekly Price
Exhibition
News
-
Trade Service
The single-layer multifunctional reactor can provide high temperature reaction (the highest temperature can reach 300℃); it can also be evacuated to do negative pressure reaction
.
The single-layer glass reactor can carry out various solvent synthesis reactions under constant temperature conditions.
The reaction part of the instrument is a controllable and fully sealed structure.
It can continuously inhale various liquids and gases by using negative pressure, and can also perform reflux or distillation at different temperatures
.
So, how to maintain and maintain the single-layer multifunctional reactor? 1.
Carefully check the instrument before use, whether the glass bottle is damaged, whether the interfaces are consistent, and pay attention to handle it with care
.
2.
Wipe each interface with a soft cloth (can be replaced with a napkin), and then apply a little vacuum grease
.
(Be sure to cover the vacuum grease after use to prevent lime and sand from entering
.
) 3.
The interfaces of the glass reactor should not be tightened too tightly, and should be loosened regularly to avoid long-term locking and causing the connector to be killed
.
4.
Turn on the power switch first, and then let the machine run from slow to fast.
When the machine is stopped, keep the machine in a stopped state, and then turn off the switch
.
5.
The PTFE switches everywhere should not be over-tightened, which will easily damage the glass
.
6.
After each use, all kinds of oil stains, stains and solvent residues left on the surface of the machine must be wiped off with a soft cloth to keep it clean
.
7.
Unscrew each PTFE switch after stopping, and the PTFE piston will be deformed if it is still in the working state for a long time
.
8.
Clean the sealing ring regularly.
The method is: remove the sealing ring, check whether there is dirt on the shaft, wipe it with a soft cloth, then apply a little vacuum grease, and reinstall it to keep the shaft and the sealing ring smooth
.
9.
The electrical part must not enter the water, and it is strictly forbidden to get wet
.
10.
It is necessary to purchase the original authentic accessories.
The random use of other accessories will cause fatal damage to the machine.
.
11.
When doing any repairs or inspections to the glass reactor, be sure to cut off the power supply and water source first
.
.
The single-layer glass reactor can carry out various solvent synthesis reactions under constant temperature conditions.
The reaction part of the instrument is a controllable and fully sealed structure.
It can continuously inhale various liquids and gases by using negative pressure, and can also perform reflux or distillation at different temperatures
.
So, how to maintain and maintain the single-layer multifunctional reactor? 1.
Carefully check the instrument before use, whether the glass bottle is damaged, whether the interfaces are consistent, and pay attention to handle it with care
.
2.
Wipe each interface with a soft cloth (can be replaced with a napkin), and then apply a little vacuum grease
.
(Be sure to cover the vacuum grease after use to prevent lime and sand from entering
.
) 3.
The interfaces of the glass reactor should not be tightened too tightly, and should be loosened regularly to avoid long-term locking and causing the connector to be killed
.
4.
Turn on the power switch first, and then let the machine run from slow to fast.
When the machine is stopped, keep the machine in a stopped state, and then turn off the switch
.
5.
The PTFE switches everywhere should not be over-tightened, which will easily damage the glass
.
6.
After each use, all kinds of oil stains, stains and solvent residues left on the surface of the machine must be wiped off with a soft cloth to keep it clean
.
7.
Unscrew each PTFE switch after stopping, and the PTFE piston will be deformed if it is still in the working state for a long time
.
8.
Clean the sealing ring regularly.
The method is: remove the sealing ring, check whether there is dirt on the shaft, wipe it with a soft cloth, then apply a little vacuum grease, and reinstall it to keep the shaft and the sealing ring smooth
.
9.
The electrical part must not enter the water, and it is strictly forbidden to get wet
.
10.
It is necessary to purchase the original authentic accessories.
The random use of other accessories will cause fatal damage to the machine.
.
11.
When doing any repairs or inspections to the glass reactor, be sure to cut off the power supply and water source first
.
