-
Categories
-
Pharmaceutical Intermediates
-
Active Pharmaceutical Ingredients
-
Food Additives
- Industrial Coatings
- Agrochemicals
- Dyes and Pigments
- Surfactant
- Flavors and Fragrances
- Chemical Reagents
- Catalyst and Auxiliary
- Natural Products
- Inorganic Chemistry
-
Organic Chemistry
-
Biochemical Engineering
- Analytical Chemistry
-
Cosmetic Ingredient
- Water Treatment Chemical
-
Pharmaceutical Intermediates
Promotion
ECHEMI Mall
Wholesale
Weekly Price
Exhibition
News
-
Trade Service
Definition of puncture strength of WDC-5 lithium battery diaphragm puncture strength tester: Install a test piece with a diameter of 100mm on the sample film fixing clip, and then use a steel needle with a diameter of 1.
0mm and a spherical tip radius of 0.
5mm to (50 ±5) The speed of mm/min is used to remove the top puncture, and the large load of the steel needle penetrating the test piece is read.
The number of test pieces is more than 5, and the average value is taken
.
The puncture resistance of the plastic film can more comprehensively reflect the puncture resistance of the film
.
The puncture resistance of plastic film or composite film is one of the important indicators for testing packaging materials, especially for the packaging of steamed meat products, such as poultry meat products, in which bones have strong puncture ability to packaging materials.
Therefore, testing packaging materials The puncture strength is a must-check item for packaging material manufacturers and food manufacturers
.
The experimental method is clearly specified in GB/T 10004-2008 (plastic composite film for packaging, bag dry composite, extrusion composite)
.
Product introduction: 1.
It is mainly used for the testing of mechanical properties such as tensile, compression, bending, shearing, peeling, tearing, puncturing and bursting of various metals, non-metals and composite materials
.
The system adopts microcomputer closed-loop or open-loop control, has a wide and accurate range of loading speed and force measurement, and has high precision and sensitivity for the measurement and control of load and displacement
.
2.
This equipment can be equipped with puncture aids for geomembrane, plastic film, etc.
to complete the test of puncture strength; with corresponding tensile aids, it can also measure the tensile properties of the film
.
Selected according to customer needs
.
Applicable standards: (if there are other standard requirements, they can be produced according to the national standard) 1.
GB/T 2611-2007 "General Technical Requirements for Testing Machines" 2.
JB/T 7406.
1-1994 "Testing Machine Terminology Material Testing Machine" 3, GB-T 17643-2011 Geosynthetic Polyethylene Geomembrane Appendix C Puncture 4, CJT 234-2006 High Density Polyethylene Geomembrane for Landfills 5, GB/T 16491-2008 "Electronic Universal Testing Machine" 6, GB/T 16825.
1-2008 "Inspection of Static Uniaxial Testing Machine Part 1: Inspection and Calibration of Tensile and (or) Compressive Testing Machine Force Measuring System" 7, GB/T 22066-2008 "Static Uniaxial Testing Machine" Evaluation of Computer Data Acquisition System" 8, JJG 139-1999 "Tension, Compression and Universal Material Testing Machine" 9, JB/T 6146-2007 "Technical Conditions for Extensometers" 10, JB/T 6147-2007 "Testing Machine Packaging, Packaging Marks, Technical Requirements for Storage and Transportation" 11, GB/T 228.
1-2010 "Metal Materials Tensile Test Part 1: Test Methods at Room Temperature" 12, GB/T 7314-2005 "Room Temperature Compression Test Methods for Metal Materials" 13, GB/T T 232-2010 "Bending Test Method for Metal Materials" and other non-metal test standards are based on the national standard GB/T 10004-2008 Research and development and design of requirements for puncture strength testers in plastic composite films for packaging, bag dry lamination, and extrusion lamination Film puncture force tester, also known as film puncture force tester, film puncture force tester, is professionally used to test the puncture force of plastic films.
Through the test, it can effectively monitor whether the film puncture force meets the requirements, and optimize production for improvement.
The process provides detection basis, and the instrument can also be used for injection needle puncture force test and rubber stopper puncture force test
.
Main parameters: Test force range: 30N/50N/100N/200N/500N/1000N Accuracy class: 0.
1 Number of sensors: 2 (optional two) Drive system: High-performance imported Panasonic servo drive system Beam moving speed: 0.
05 ~ 1000 mm/min (continuously adjustable, process return), the accuracy of the moving speed of the beam: ±1% Tension and compression Large stroke: 600mm Number of single test samples: 1 piece Sample width: 30mm (standard); 50mm (optional) chuck clamping form: manual clamping (standard); pneumatic clamping (optional) Power supply: AC 220V 50Hz/120V 60Hz Dimensions: 480mm(L)×480mm(W)×1100mm(H ) Approx.
net weight: 50kg Standard configuration: host, computer, puncture force fixture, communication cable Label: lithium battery diaphragm puncture strength tester
0mm and a spherical tip radius of 0.
5mm to (50 ±5) The speed of mm/min is used to remove the top puncture, and the large load of the steel needle penetrating the test piece is read.
The number of test pieces is more than 5, and the average value is taken
.
The puncture resistance of the plastic film can more comprehensively reflect the puncture resistance of the film
.
The puncture resistance of plastic film or composite film is one of the important indicators for testing packaging materials, especially for the packaging of steamed meat products, such as poultry meat products, in which bones have strong puncture ability to packaging materials.
Therefore, testing packaging materials The puncture strength is a must-check item for packaging material manufacturers and food manufacturers
.
The experimental method is clearly specified in GB/T 10004-2008 (plastic composite film for packaging, bag dry composite, extrusion composite)
.
Product introduction: 1.
It is mainly used for the testing of mechanical properties such as tensile, compression, bending, shearing, peeling, tearing, puncturing and bursting of various metals, non-metals and composite materials
.
The system adopts microcomputer closed-loop or open-loop control, has a wide and accurate range of loading speed and force measurement, and has high precision and sensitivity for the measurement and control of load and displacement
.
2.
This equipment can be equipped with puncture aids for geomembrane, plastic film, etc.
to complete the test of puncture strength; with corresponding tensile aids, it can also measure the tensile properties of the film
.
Selected according to customer needs
.
Applicable standards: (if there are other standard requirements, they can be produced according to the national standard) 1.
GB/T 2611-2007 "General Technical Requirements for Testing Machines" 2.
JB/T 7406.
1-1994 "Testing Machine Terminology Material Testing Machine" 3, GB-T 17643-2011 Geosynthetic Polyethylene Geomembrane Appendix C Puncture 4, CJT 234-2006 High Density Polyethylene Geomembrane for Landfills 5, GB/T 16491-2008 "Electronic Universal Testing Machine" 6, GB/T 16825.
1-2008 "Inspection of Static Uniaxial Testing Machine Part 1: Inspection and Calibration of Tensile and (or) Compressive Testing Machine Force Measuring System" 7, GB/T 22066-2008 "Static Uniaxial Testing Machine" Evaluation of Computer Data Acquisition System" 8, JJG 139-1999 "Tension, Compression and Universal Material Testing Machine" 9, JB/T 6146-2007 "Technical Conditions for Extensometers" 10, JB/T 6147-2007 "Testing Machine Packaging, Packaging Marks, Technical Requirements for Storage and Transportation" 11, GB/T 228.
1-2010 "Metal Materials Tensile Test Part 1: Test Methods at Room Temperature" 12, GB/T 7314-2005 "Room Temperature Compression Test Methods for Metal Materials" 13, GB/T T 232-2010 "Bending Test Method for Metal Materials" and other non-metal test standards are based on the national standard GB/T 10004-2008 Research and development and design of requirements for puncture strength testers in plastic composite films for packaging, bag dry lamination, and extrusion lamination Film puncture force tester, also known as film puncture force tester, film puncture force tester, is professionally used to test the puncture force of plastic films.
Through the test, it can effectively monitor whether the film puncture force meets the requirements, and optimize production for improvement.
The process provides detection basis, and the instrument can also be used for injection needle puncture force test and rubber stopper puncture force test
.
Main parameters: Test force range: 30N/50N/100N/200N/500N/1000N Accuracy class: 0.
1 Number of sensors: 2 (optional two) Drive system: High-performance imported Panasonic servo drive system Beam moving speed: 0.
05 ~ 1000 mm/min (continuously adjustable, process return), the accuracy of the moving speed of the beam: ±1% Tension and compression Large stroke: 600mm Number of single test samples: 1 piece Sample width: 30mm (standard); 50mm (optional) chuck clamping form: manual clamping (standard); pneumatic clamping (optional) Power supply: AC 220V 50Hz/120V 60Hz Dimensions: 480mm(L)×480mm(W)×1100mm(H ) Approx.
net weight: 50kg Standard configuration: host, computer, puncture force fixture, communication cable Label: lithium battery diaphragm puncture strength tester
