-
Categories
-
Pharmaceutical Intermediates
-
Active Pharmaceutical Ingredients
-
Food Additives
- Industrial Coatings
- Agrochemicals
- Dyes and Pigments
- Surfactant
- Flavors and Fragrances
- Chemical Reagents
- Catalyst and Auxiliary
- Natural Products
- Inorganic Chemistry
-
Organic Chemistry
-
Biochemical Engineering
- Analytical Chemistry
-
Cosmetic Ingredient
- Water Treatment Chemical
-
Pharmaceutical Intermediates
Promotion
ECHEMI Mall
Wholesale
Weekly Price
Exhibition
News
-
Trade Service
The stainless steel sanitary filter is mainly used for the pre-filtration and fine filtration of the sterilizing liquid.
The materials in contact with the liquid are made of 316L or 304 stainless steel, and are mechanically or electrolytically polished to provide durability and corrosion resistance.
performance
.
The structure has no hygienic dead corners, and the filter drain valve, air release valve, material liquid inlet and filter socket are easy to clean, which can be completely sterilized and hygienic, drained thoroughly, and there is no residual liquid concern
.
Installation and use of stainless steel sanitary filter: Connect the interface flange to the slurry output pipeline to make the slurry flow evenly through the filter, and determine the cleaning cycle after a period of trial
.
When cleaning, first loosen the clamping screw on the cover, take out the casing cover part, and then pull out the magnetic rod, and the ferrous impurities adsorbed on the casing can automatically fall off
.
After cleaning, when installing, first put the casing into the cylinder, tighten the clamping screw, and then insert the magnetic rod cover into the casing, and then continue to use
.
Maintenance methods of stainless steel sanitary filter: 1.
The core part of the filter is the filter element, which is composed of special materials and should be damaged and needs special protection; 2.
When the filter works for a period of time, the filter The filter element holds a certain amount of impurities.
At this time, the pressure drop increases and the flow rate will decrease.
It is necessary to remove the impurities in the filter in time and clean the filter element at the same time; 3.
When removing impurities, pay special attention to the precision filter element, which must not be deformed or damaged.
, otherwise, the purity of the filter medium after filtration will not meet the design requirements; 4.
Certain precision filter elements cannot be used repeatedly, such as bag filter elements, polypropylene filter elements, etc.
5.
If the filter element is found to be deformed or Damaged, need to be replaced immediately
.
The materials in contact with the liquid are made of 316L or 304 stainless steel, and are mechanically or electrolytically polished to provide durability and corrosion resistance.
performance
.
The structure has no hygienic dead corners, and the filter drain valve, air release valve, material liquid inlet and filter socket are easy to clean, which can be completely sterilized and hygienic, drained thoroughly, and there is no residual liquid concern
.
Installation and use of stainless steel sanitary filter: Connect the interface flange to the slurry output pipeline to make the slurry flow evenly through the filter, and determine the cleaning cycle after a period of trial
.
When cleaning, first loosen the clamping screw on the cover, take out the casing cover part, and then pull out the magnetic rod, and the ferrous impurities adsorbed on the casing can automatically fall off
.
After cleaning, when installing, first put the casing into the cylinder, tighten the clamping screw, and then insert the magnetic rod cover into the casing, and then continue to use
.
Maintenance methods of stainless steel sanitary filter: 1.
The core part of the filter is the filter element, which is composed of special materials and should be damaged and needs special protection; 2.
When the filter works for a period of time, the filter The filter element holds a certain amount of impurities.
At this time, the pressure drop increases and the flow rate will decrease.
It is necessary to remove the impurities in the filter in time and clean the filter element at the same time; 3.
When removing impurities, pay special attention to the precision filter element, which must not be deformed or damaged.
, otherwise, the purity of the filter medium after filtration will not meet the design requirements; 4.
Certain precision filter elements cannot be used repeatedly, such as bag filter elements, polypropylene filter elements, etc.
5.
If the filter element is found to be deformed or Damaged, need to be replaced immediately
.
