-
Categories
-
Pharmaceutical Intermediates
-
Active Pharmaceutical Ingredients
-
Food Additives
- Industrial Coatings
- Agrochemicals
- Dyes and Pigments
- Surfactant
- Flavors and Fragrances
- Chemical Reagents
- Catalyst and Auxiliary
- Natural Products
- Inorganic Chemistry
-
Organic Chemistry
-
Biochemical Engineering
- Analytical Chemistry
-
Cosmetic Ingredient
- Water Treatment Chemical
-
Pharmaceutical Intermediates
Promotion
ECHEMI Mall
Wholesale
Weekly Price
Exhibition
News
-
Trade Service
An oscillator is an energy conversion device that converts DC electrical energy into AC electrical energy with a frequency, and the circuit formed by it is called an oscillator circui.
There are two main types of oscillators: harmonic oscillators and relaxation oscillator.
An oscillator is an electronic component used to generate a repeating electronic signal (usually a sine or square wave.
The circuit composed of it is called an oscillator circui.
An electronic circuit or device that can convert direct current into an alternating current signal with a frequency outpu.
There are many types, which can be divided into self-excited oscillators and other-excited oscillators according to the oscillation excitation mode; according to the circuit structure, they can be divided into resistance-capacitor oscillators, inductor-capacitor oscillators, crystal oscillators, tuning fork oscillators, et.
; according to the output waveform, they can be divided into For sine wave, square wave, sawtooth wave and other oscillator.
Widely used in electronic industry, scientific research and so o.
Use processLoad the test bottle and keep it balance.
If it is a dual-function model, set the oscillation mod.
Turn on the power, and set the timer according to the scale on the surface of the machin.
If you need to work for a long time, adjust the timer to the "normally open" positio.
Turn on the power switch and set the constant temperature: (1) Put the small control switch in the "setting" section, the temperature displayed on the display is the set temperature, adjust the knob and set it to the temperature you need for wor.
Ye.
(The working temperature you set should be higher than the ambient temperatur.
At this time, the machine starts to heat up, and the yellow indicator light is on, otherwise the machine will not work) (2) Put the small switch of the control part on the "measurement" end, and the temperature displayed on the display at this time It is the actual temperature of the air in the test bo.
With the change of the temperature in the box, the displayed number will also change accordingl.
(3) When the heating reaches the temperature you need, the heating will automatically stop and the green indicator light will be on; when the heat in the test box is dissipated and is lower than the temperature you set, a new round of heating will start agai.
Turn on the oscillation device: (1) Turn on the oscillation switch on the control panel, the indicator light is o.
(2) Adjust the oscillation speed knob to the desired oscillation frequenc.
After work, cut off the power supply, and set the speed control knob and temperature control knob to the low poin.
Clean the machine and keep it clea.
There are two main types of oscillators: harmonic oscillators and relaxation oscillator.
An oscillator is an electronic component used to generate a repeating electronic signal (usually a sine or square wave.
The circuit composed of it is called an oscillator circui.
An electronic circuit or device that can convert direct current into an alternating current signal with a frequency outpu.
There are many types, which can be divided into self-excited oscillators and other-excited oscillators according to the oscillation excitation mode; according to the circuit structure, they can be divided into resistance-capacitor oscillators, inductor-capacitor oscillators, crystal oscillators, tuning fork oscillators, et.
; according to the output waveform, they can be divided into For sine wave, square wave, sawtooth wave and other oscillator.
Widely used in electronic industry, scientific research and so o.
Use processLoad the test bottle and keep it balance.
If it is a dual-function model, set the oscillation mod.
Turn on the power, and set the timer according to the scale on the surface of the machin.
If you need to work for a long time, adjust the timer to the "normally open" positio.
Turn on the power switch and set the constant temperature: (1) Put the small control switch in the "setting" section, the temperature displayed on the display is the set temperature, adjust the knob and set it to the temperature you need for wor.
Ye.
(The working temperature you set should be higher than the ambient temperatur.
At this time, the machine starts to heat up, and the yellow indicator light is on, otherwise the machine will not work) (2) Put the small switch of the control part on the "measurement" end, and the temperature displayed on the display at this time It is the actual temperature of the air in the test bo.
With the change of the temperature in the box, the displayed number will also change accordingl.
(3) When the heating reaches the temperature you need, the heating will automatically stop and the green indicator light will be on; when the heat in the test box is dissipated and is lower than the temperature you set, a new round of heating will start agai.
Turn on the oscillation device: (1) Turn on the oscillation switch on the control panel, the indicator light is o.
(2) Adjust the oscillation speed knob to the desired oscillation frequenc.
After work, cut off the power supply, and set the speed control knob and temperature control knob to the low poin.
Clean the machine and keep it clea.
