-
Baling Petrochemical's o-cresol epoxy resin output hits a new high
Time of Update: 2021-12-01
For a long time, the large deviation of the solid content of the o-cresol unit results in poor liquid separation effect and more waste polymer; product viscosity fluctuations affect the first pass rate, and the need to repeatedly mix materials increases the energy consumption of the device; the long washing process time affects production Efficiency coating online coatingol.
-
Development of environmentally friendly high-performance two-component waterborne epoxy paint!
Time of Update: 2021-12-01
After using two-component waterborne epoxy coatings instead of traditional oil-based coatings, the performance of the paint film cannot be greatly reduced, such as water resistance, salt spray resistance, and chemical resistance .
-
Hunsite builds a new project with an annual output of 80,000 tons of epoxy curing agent and 10,000 tons of epoxy coatings
Time of Update: 2021-12-01
On October 17, the Jingzhou City Ecological Environment Bureau issued the "Publicity of the Environmental Impact Assessment of the Newly-built Project of Hengsite Chemical (Jingzhou) Co.
-
Zhongke Refinery successfully trial-produced high melt index polypropylene resin
Time of Update: 2021-11-12
Recently, the 200,000 tons/year polypropylene plant of Zhongke Refining & Chemical has successfully trial-produced high melt index polypropylene products EP548U and EP648U .
It is mainly used to manufacture bottles, cups and other household utensils, as well as thin-walled rigid parts that require high impact resistance .
-
[Literature Interpretation] Is it feasible to synthesize UV-curable polyurethane acrylate using a solvent-free one-pot method?
Time of Update: 2021-11-11
Keywords: castor oil one-pot solvent-free polyurethane acrylate UV curable coating Background introduction UV curing technology is widely used in coatings, inks, adhesives and other industries, and has the advantages of high efficiency, energy saving, economy, effectiveness, and environmental protection .
-
Preparation of high temperature resistant powder coating
Time of Update: 2021-11-11
At present, the more commonly used high temperature resistant powder coatings for BBQ are around 350℃, while the exhaust pipe and radiator require temperature resistance of around 500℃, and are resistant to weathering.
-
The completion and acceptance of the 55kt/a epichlorohydrin project of Fujian Haobang Chemical Co., Ltd.
Time of Update: 2021-11-11
organized experts to inspect and accept the project in accordance with the "Fujian Haobang Chemical Co.
Fujian Haobang has built a 55kt/a epichlorohydrin project and a 70kt/a glycerin purification project, both of which have been completed .
-
New UV Adhesive Resin FSP8672
Time of Update: 2021-11-11
It mainly examines the resin's adhesion, curing speed, boiling resistance, hardness, tensile strength, and apparent properties.
FSP8672 has excellent performance in water boiling resistance and high temperature and humidity tests.
-
Fangxin FX-W9286 Acrylic resin for water-based glass baking paint
Time of Update: 2021-11-11
Suitable for electroplating varnish, glass baking paint coating online coatingol.
When using, please test the stability of the resin in the solvent and the influence of the solvent on the paint film .
-
The main body of the lighthouse coating Nangang project, which escorted the aerospace field, was successfully topped off!
Time of Update: 2021-11-01
In the history of China's industrial development, "Lighthouse" paint represents the pride of China's national paint industry, and has been researched, produced and applied in high-precision fields such as national key military projects and special coatings as a coating protection in the domestic aerospace field.
-
Different ways to achieve better wettability of water-based coatings!
Time of Update: 2021-11-01
Different ways to achieve better wettabilityA classic way to increase the wettability of the substrate is to use an additive that can reduce the surface tension of the coating to be coated.
-
Phase transformation and interface change of tempered glass ink
Time of Update: 2021-11-01
It can be seen from Figures 2d and e that the low-melting glass powder further melts, flows and spreads into a continuous phase at 600°C and 700°C, which has replaced the organic resin film layer and adhered to the high-temperature resistant pigments and fillers in the coating.
-
Covestro expands bio-based resin portfolio to promote sustainability of decorative coatings
Time of Update: 2021-11-01
Covestro will use its leading position in some bio-based resin innovations to develop its Recovery® series resins and value-added services to meet the needs of its customers and the market .
-
The epidemic is under control, the mask business of Shengquan Group has shrunk by 90%, but the performance of the resin business is very strong
Time of Update: 2021-11-01
The decline in operating income was mainly due to the gradual improvement of the domestic and foreign epidemic situation and the sharp shrinkage of the sanitary protection product market: From January to September 2020, Shengquan Group’s sanitary protection product business achieved sales revenue of more than 2 billion yuan, which was only 230 million yuan in the same period this year, a decrease of 89 % .
-
Wanhua Chemical: Revenue exceeded 100 billion yuan in the first three quarters, net profit increased by 265%
Time of Update: 2021-11-01
Regarding changes in performance, Wanhua Chemical stated that during the reporting period, global vaccine inoculation has continued to repair consumption and manufacturing in major economies, and the supply of basic energy is tight, and prices have risen significantly.
-
High-solid and low-viscosity UV one-coating resin LuCure5956
Time of Update: 2021-11-01
For ultraviolet light, different pigments have different absorption rates and have different effects on the photocuring speed of the coating .
Boil-resistantThe paint film cured by LuCure 5956 has good hydrophobicity and high crosslinking density .
-
Quality inspection and repair knowledge of glass fiber reinforced plastic pultrusion process products
Time of Update: 2021-10-19
In the production process, the types and causes of defects in pultruded products are analyzed as follows:(1) Fiber and felt accumulation on the surface Result: Reinforcement materials are entangled and squeezed at the entrance of the mold, resulting in increased resistance of the product in the mold, and in severe cases, the product may be damaged .
-
Shengquan Group releases new products, phenolic resin market is expected to increase by 2 million tons
Time of Update: 2021-10-19
The technological breakthrough of Shengquan Group has a far-reaching impact on the energy saving and carbon reduction of the electrolytic aluminum industry chain .
Phenolic resin carbon anode can effectively promote energy saving and carbon reduction in the electrolytic aluminum industry chain .
-
Lanxess is a lightweight composite material based on polyamide 6 used in the load compartment of luxury cars
Time of Update: 2021-10-19
A new application of these composite materials from LANXESS is the manufacture of load compartments installed on Mercedes-Benz S-Class cars to accommodate 48V on-board power batteries .
-
Hexion Holdings announces plans to split into two independent companies
Time of Update: 2021-10-19
Hexion Holdings maintains a strong momentum, in line with the market's growing demand for environmentally friendly construction and coatings After the separation, Hexion Holdings will include the company's existing adhesive and Versatic Acids™ and derivative product lines .
