-
Categories
-
Pharmaceutical Intermediates
-
Active Pharmaceutical Ingredients
-
Food Additives
- Industrial Coatings
- Agrochemicals
- Dyes and Pigments
- Surfactant
- Flavors and Fragrances
- Chemical Reagents
- Catalyst and Auxiliary
- Natural Products
- Inorganic Chemistry
-
Organic Chemistry
-
Biochemical Engineering
- Analytical Chemistry
-
Cosmetic Ingredient
- Water Treatment Chemical
-
Pharmaceutical Intermediates
Promotion
ECHEMI Mall
Wholesale
Weekly Price
Exhibition
News
-
Trade Service
The broad understanding of the reactor is that there is a physical or chemical reaction container.
Through the structural design and parameter configuration of the container, the heating, evaporation, cooling and low-speed mixing functions required by the process are realized
.
Reactors are widely used in the fields of petroleum, chemical industry, rubber, pesticides, dyes, medicine and food.
, decomposition pot, polymerization kettle, etc.
; the materials are generally carbon-manganese steel, stainless steel, zirconium, nickel-based (Hastelloy, Monel, Inconel) alloys and other composite materials
.
Installation Precautions 1.
The autoclave should be placed indoors
.
When equipping multiple autoclaves, they should be placed separately
.
Each operating room should have an outlet directly leading to the outdoors or passage, and the equipment location should be well ventilated
.
2.
When installing the kettle cover, the sealing surfaces between the kettle body and the kettle cover should be prevented from colliding with each other
.
Carefully place the kettle cover on the kettle body in a fixed position.
When tightening the main nut, gradually tighten it diagonally and symmetrically
.
The force should be uniform, and the lid of the kettle should not be tilted to one side to achieve a good sealing effect
.
3.
At the connection between the positive and negative nuts, only the positive and negative nuts are allowed to be rotated.
The two arc sealing surfaces must not be rotated relative to each other.
When all the nut thread joints are assembled, lubricating oil should be applied
.
4.
The needle-type valve is sealed by the line.
It only needs to gently turn the valve needle and press the cover tightly to achieve a good sealing effect
.
5.
Move the rotating body on the kettle by hand to check whether the operation is flexible
.
6.
The controller should be placed flat on the operating table, the working environment temperature is 10-40 ℃, the relative humidity is less than 85%, and the surrounding medium does not contain conductive dust and corrosive gas
.
7.
Check whether the movable parts and fixed contacts on the front panel and the rear panel are normal, open the upper cover, check whether the contact of the connector is loose, and whether there is damage or corrosion caused by poor transportation and storage
.
8.
The controller should be grounded reliably
.
9.
Connect all the wires, including the power wire, the electric furnace wire between the controller and the kettle, the motor wire, the temperature sensor and the tachometer wire
.
10.
Turn on the "power" air main switch on the panel, and the digital display should display
.
Through the structural design and parameter configuration of the container, the heating, evaporation, cooling and low-speed mixing functions required by the process are realized
.
Reactors are widely used in the fields of petroleum, chemical industry, rubber, pesticides, dyes, medicine and food.
, decomposition pot, polymerization kettle, etc.
; the materials are generally carbon-manganese steel, stainless steel, zirconium, nickel-based (Hastelloy, Monel, Inconel) alloys and other composite materials
.
Installation Precautions 1.
The autoclave should be placed indoors
.
When equipping multiple autoclaves, they should be placed separately
.
Each operating room should have an outlet directly leading to the outdoors or passage, and the equipment location should be well ventilated
.
2.
When installing the kettle cover, the sealing surfaces between the kettle body and the kettle cover should be prevented from colliding with each other
.
Carefully place the kettle cover on the kettle body in a fixed position.
When tightening the main nut, gradually tighten it diagonally and symmetrically
.
The force should be uniform, and the lid of the kettle should not be tilted to one side to achieve a good sealing effect
.
3.
At the connection between the positive and negative nuts, only the positive and negative nuts are allowed to be rotated.
The two arc sealing surfaces must not be rotated relative to each other.
When all the nut thread joints are assembled, lubricating oil should be applied
.
4.
The needle-type valve is sealed by the line.
It only needs to gently turn the valve needle and press the cover tightly to achieve a good sealing effect
.
5.
Move the rotating body on the kettle by hand to check whether the operation is flexible
.
6.
The controller should be placed flat on the operating table, the working environment temperature is 10-40 ℃, the relative humidity is less than 85%, and the surrounding medium does not contain conductive dust and corrosive gas
.
7.
Check whether the movable parts and fixed contacts on the front panel and the rear panel are normal, open the upper cover, check whether the contact of the connector is loose, and whether there is damage or corrosion caused by poor transportation and storage
.
8.
The controller should be grounded reliably
.
9.
Connect all the wires, including the power wire, the electric furnace wire between the controller and the kettle, the motor wire, the temperature sensor and the tachometer wire
.
10.
Turn on the "power" air main switch on the panel, and the digital display should display
.
