-
Categories
-
Pharmaceutical Intermediates
-
Active Pharmaceutical Ingredients
-
Food Additives
- Industrial Coatings
- Agrochemicals
- Dyes and Pigments
- Surfactant
- Flavors and Fragrances
- Chemical Reagents
- Catalyst and Auxiliary
- Natural Products
- Inorganic Chemistry
-
Organic Chemistry
-
Biochemical Engineering
- Analytical Chemistry
-
Cosmetic Ingredient
- Water Treatment Chemical
-
Pharmaceutical Intermediates
Promotion
ECHEMI Mall
Wholesale
Weekly Price
Exhibition
News
-
Trade Service
The ultrasonic tumbling machine is composed of ultrasonic system, mechanical stirring system, refrigeration system and PLC automatic control electrical system
.
How to use the ultrasonic tumbler: 1.
First open the exhaust valve of the interlayer tank, inject water into the interlayer tank from the water inlet until the water overflows, then turn on the switch of the circulating pump to see if the circulating pump is flowing, if not, turn it on The exhaust valve of the circulating pump is used to discharge the gas in the circulating pump to make the circulating pump work normally, and then add some water to the interlayer tank until the water is full
.
2.
Set the panel parameters of the tumbler: (1) Setting of the rotation speed of the tumbler: adjust the rotation speed through the knob of the inverter, and the automatic screen display shows the rotation speed
.
(2) The adjustment range of the angle of the tumbling drum: 0°-90°, the manual screen on the display screen: press the angle +, each time increases by 5°; press the angle -, each time decreases by 5°
.
Pay attention to pressing the angle + or angle -, the speed should not be too fast or too frequently; the interval between each time should be more than 10 seconds
.
3.
Vacuum system: Before starting the automatic work, check whether the lid of the tank is closed, whether the vacuum valve is closed, and whether the tank is under normal pressure.
If the vacuum degree has been reached, put a little gas first, and then close the valve to ensure that the vacuum degree The state is not reached, otherwise the automatic process cannot be started
.
Note: The machine must be operated in strict accordance with the following instructions: 1.
The leakage protection switch must be connected before the power supply! to ensure safety! 2.
It is strictly forbidden to turn on the ultrasonic wave when the liquid is not filled with the interlayer tank, otherwise the machine will be damaged! Do not! 3.
It is strictly forbidden to dismantle or overhaul the machine with power on! To avoid electric shock! 4.
Please place the ultrasonic wave to work in a ventilated, dry and non-corrosive environment
.
.
How to use the ultrasonic tumbler: 1.
First open the exhaust valve of the interlayer tank, inject water into the interlayer tank from the water inlet until the water overflows, then turn on the switch of the circulating pump to see if the circulating pump is flowing, if not, turn it on The exhaust valve of the circulating pump is used to discharge the gas in the circulating pump to make the circulating pump work normally, and then add some water to the interlayer tank until the water is full
.
2.
Set the panel parameters of the tumbler: (1) Setting of the rotation speed of the tumbler: adjust the rotation speed through the knob of the inverter, and the automatic screen display shows the rotation speed
.
(2) The adjustment range of the angle of the tumbling drum: 0°-90°, the manual screen on the display screen: press the angle +, each time increases by 5°; press the angle -, each time decreases by 5°
.
Pay attention to pressing the angle + or angle -, the speed should not be too fast or too frequently; the interval between each time should be more than 10 seconds
.
3.
Vacuum system: Before starting the automatic work, check whether the lid of the tank is closed, whether the vacuum valve is closed, and whether the tank is under normal pressure.
If the vacuum degree has been reached, put a little gas first, and then close the valve to ensure that the vacuum degree The state is not reached, otherwise the automatic process cannot be started
.
Note: The machine must be operated in strict accordance with the following instructions: 1.
The leakage protection switch must be connected before the power supply! to ensure safety! 2.
It is strictly forbidden to turn on the ultrasonic wave when the liquid is not filled with the interlayer tank, otherwise the machine will be damaged! Do not! 3.
It is strictly forbidden to dismantle or overhaul the machine with power on! To avoid electric shock! 4.
Please place the ultrasonic wave to work in a ventilated, dry and non-corrosive environment
.
