-
Categories
-
Pharmaceutical Intermediates
-
Active Pharmaceutical Ingredients
-
Food Additives
- Industrial Coatings
- Agrochemicals
- Dyes and Pigments
- Surfactant
- Flavors and Fragrances
- Chemical Reagents
- Catalyst and Auxiliary
- Natural Products
- Inorganic Chemistry
-
Organic Chemistry
-
Biochemical Engineering
- Analytical Chemistry
-
Cosmetic Ingredient
- Water Treatment Chemical
-
Pharmaceutical Intermediates
Promotion
ECHEMI Mall
Wholesale
Weekly Price
Exhibition
News
-
Trade Service
Ultraviolet aging test box series products are suitable for the aging test of non-metallic materials with sunlight resistance and artificial light source.
The equipment (such as paint, paint, rubber, plastic and its products), has been Check the degree of aging of the relevant products and materials under the change of conditions
.
Discoloration, fading, etc.
are obtained in a short period of time
.
Using a fluorescent UV lamp as the light source, by simulating the UV radiation and condensation in natural sunlight, an accelerated weather resistance test was performed on the material to obtain the results of the material's weather resistance
.
Due to the improper operation of the staff or the influence of the environmental climate, the service life of the UV aging test box will be shortened.
How to use and place the UV aging test box correctly to prolong the service life? The technical department below summarizes the following points, please check carefully: UV aging test box placement conditions: 1.
After installation, there should be enough maintenance space between the equipment and the adjacent walls or other equipment; 2.
In order to stably use the test equipment The function and performance should be selected in a place where the annual temperature is 15℃～28℃ and the relative humidity is not more than 85%; 3.
It should be installed in a place far away from combustibles, explosives and high temperature heat sources; 4.
It should be installed in a place with less dust 5.
It should be installed as close to the power supply as possible; 6.
It should be installed in a place without direct sunlight; 7.
It should be installed in a well-ventilated place; 8.
The ambient temperature of the installation place should not change rapidly; 9.
It should be installed on a level ground (use a spirit level to determine the level on the ground during installation); Conditions of use of the UV aging test chamber: 1.
The sensing device in the working room should not be subjected to strong impact
.
2.
Non-professional operators are not allowed to operate at will
.
3.
When the equipment fails to troubleshoot by itself, please contact the manufacturer
.
4.
During the operation of the equipment, it is necessary to maintain sufficient water source
.
5.
Because ultraviolet radiation has a strong hazard to personnel (especially eyes), operators should minimize exposure to ultraviolet rays (contact time should be <1min)
.
It is recommended that operators wear protective goggles and protective covers
.
6.
The time for opening the box door should be minimized during the test phase
.
7.
If you need to use it again after a long time, you must carefully check the water source, power supply and various components, and then start the equipment after confirming that it is correct
.
The equipment (such as paint, paint, rubber, plastic and its products), has been Check the degree of aging of the relevant products and materials under the change of conditions
.
Discoloration, fading, etc.
are obtained in a short period of time
.
Using a fluorescent UV lamp as the light source, by simulating the UV radiation and condensation in natural sunlight, an accelerated weather resistance test was performed on the material to obtain the results of the material's weather resistance
.
Due to the improper operation of the staff or the influence of the environmental climate, the service life of the UV aging test box will be shortened.
How to use and place the UV aging test box correctly to prolong the service life? The technical department below summarizes the following points, please check carefully: UV aging test box placement conditions: 1.
After installation, there should be enough maintenance space between the equipment and the adjacent walls or other equipment; 2.
In order to stably use the test equipment The function and performance should be selected in a place where the annual temperature is 15℃～28℃ and the relative humidity is not more than 85%; 3.
It should be installed in a place far away from combustibles, explosives and high temperature heat sources; 4.
It should be installed in a place with less dust 5.
It should be installed as close to the power supply as possible; 6.
It should be installed in a place without direct sunlight; 7.
It should be installed in a well-ventilated place; 8.
The ambient temperature of the installation place should not change rapidly; 9.
It should be installed on a level ground (use a spirit level to determine the level on the ground during installation); Conditions of use of the UV aging test chamber: 1.
The sensing device in the working room should not be subjected to strong impact
.
2.
Non-professional operators are not allowed to operate at will
.
3.
When the equipment fails to troubleshoot by itself, please contact the manufacturer
.
4.
During the operation of the equipment, it is necessary to maintain sufficient water source
.
5.
Because ultraviolet radiation has a strong hazard to personnel (especially eyes), operators should minimize exposure to ultraviolet rays (contact time should be <1min)
.
It is recommended that operators wear protective goggles and protective covers
.
6.
The time for opening the box door should be minimized during the test phase
.
7.
If you need to use it again after a long time, you must carefully check the water source, power supply and various components, and then start the equipment after confirming that it is correct
.
