-
Categories
-
Pharmaceutical Intermediates
-
Active Pharmaceutical Ingredients
-
Food Additives
- Industrial Coatings
- Agrochemicals
- Dyes and Pigments
- Surfactant
- Flavors and Fragrances
- Chemical Reagents
- Catalyst and Auxiliary
- Natural Products
- Inorganic Chemistry
-
Organic Chemistry
-
Biochemical Engineering
- Analytical Chemistry
-
Cosmetic Ingredient
- Water Treatment Chemical
-
Pharmaceutical Intermediates
Promotion
ECHEMI Mall
Wholesale
Weekly Price
Exhibition
News
-
Trade Service
Ureteral Fixation Strength Tester The ureter is located in the retroperitoneum, which is a tubular structure composed of muscle and mucosa, which starts from the renal pelvis and ends at the bladder triangle
.
Male tube length is 27-30 cm, with an average of 28 cm; female tube length is 25-28 cm, with an average of 26 cm
.
The right side is about 1 cm shorter than the left side
.
Clinically, the ureter is divided into upper, middle and lower segments, which can also be called abdominal segment, pelvic segment, and bladder segment: the abdominal segment starts from the junction of the renal pelvis and ureter to the point where it crosses the iliac artery
.
Pelvic segment, from the iliac artery to the bladder wall
.
The bladder segment runs obliquely from the bladder wall to the bladder mucosa and the opening of the ureter
.
The ureteral fixation strength tester is composed of a programmable controller, a touch screen, a pressure sensor, a pressurizing device, an on-board printer, etc.
, with Chinese and English menu display, and man-machine dialogue to set various parameters to automatically run the test
.
Production units, batches can be arbitrarily input, easy to operate
.
And the use of three-level password, information security and reliability
.
Product specifications, test pressure value setting, holding time setting, print setting, test, pressurization, decompression, time, calibration, verification,
etc.
Onboard print test data
.
Real-time display of test pressure value, hold time and other data
.
And the test data and results are printed out by the printer
.
Suitable for infusion sets, blood transfusion sets, infusion needles, anesthesia pack filters, pipelines, catheters, quick connectors,
etc.
1.
Product overview: The ureteral fixation strength tester is suitable for infusion sets, blood transfusion sets, infusion needles, anesthesia pack filters, pipelines, catheters, quick connectors, etc.
.
2.
The test standard mainly uses YYT 0872-2013.
3.
Technical parameters Greater than ±1% of reading
.
3 Test duration: 0.
1 seconds to 99.
9 minutes, the error is not more than ± 0.
1S
.
4 Product net weight: 12kg5 Dimensions: 430×590×370 (mm) 6 Power supply: AC90V-240V/50Hz (adaptive wide voltage) 7 Machine power: 70W8 Programmable controller: PLC+ARM9 Touch screen: 7 inch K600+ core / Dot matrix 65 colors 800*480 resolution 10 Speed range: 0-800mm/min can be selected according to the customer 11, configure a constant temperature tank 0-99 degrees, can set the temperature at will 4, configure the list fixture 1 set of pressure measurement Mechanism: Built-in Printer: On-board Dot Matrix Printer
.
Male tube length is 27-30 cm, with an average of 28 cm; female tube length is 25-28 cm, with an average of 26 cm
.
The right side is about 1 cm shorter than the left side
.
Clinically, the ureter is divided into upper, middle and lower segments, which can also be called abdominal segment, pelvic segment, and bladder segment: the abdominal segment starts from the junction of the renal pelvis and ureter to the point where it crosses the iliac artery
.
Pelvic segment, from the iliac artery to the bladder wall
.
The bladder segment runs obliquely from the bladder wall to the bladder mucosa and the opening of the ureter
.
The ureteral fixation strength tester is composed of a programmable controller, a touch screen, a pressure sensor, a pressurizing device, an on-board printer, etc.
, with Chinese and English menu display, and man-machine dialogue to set various parameters to automatically run the test
.
Production units, batches can be arbitrarily input, easy to operate
.
And the use of three-level password, information security and reliability
.
Product specifications, test pressure value setting, holding time setting, print setting, test, pressurization, decompression, time, calibration, verification,
etc.
Onboard print test data
.
Real-time display of test pressure value, hold time and other data
.
And the test data and results are printed out by the printer
.
Suitable for infusion sets, blood transfusion sets, infusion needles, anesthesia pack filters, pipelines, catheters, quick connectors,
etc.
1.
Product overview: The ureteral fixation strength tester is suitable for infusion sets, blood transfusion sets, infusion needles, anesthesia pack filters, pipelines, catheters, quick connectors, etc.
.
2.
The test standard mainly uses YYT 0872-2013.
3.
Technical parameters Greater than ±1% of reading
.
3 Test duration: 0.
1 seconds to 99.
9 minutes, the error is not more than ± 0.
1S
.
4 Product net weight: 12kg5 Dimensions: 430×590×370 (mm) 6 Power supply: AC90V-240V/50Hz (adaptive wide voltage) 7 Machine power: 70W8 Programmable controller: PLC+ARM9 Touch screen: 7 inch K600+ core / Dot matrix 65 colors 800*480 resolution 10 Speed range: 0-800mm/min can be selected according to the customer 11, configure a constant temperature tank 0-99 degrees, can set the temperature at will 4, configure the list fixture 1 set of pressure measurement Mechanism: Built-in Printer: On-board Dot Matrix Printer
